Get The App From Play Store!

Skip to main content

Heat Resistant Glass Sealant - 310ml Stock Number: ES914819

High performance, heat resistant silicon sealant for repairing oven glass and door fixings.

Product Q&A

Ask a Question
By rich6 - - 29 September 2009
  • If it was originally glued on and not screwed then this will do the job perfectly. You need to leave it a few hours (eg overnight) to set fully before use. By hemlock1961 - East Sussex - 13 February 2010
  • In my opinion yes, but even if it doesn't it won't cost the earth to find out. I say give it a go! good luck. By femfixit - Essex - 11 November 2009
Answer this question

Our 10+ year old oven's plastic door handle has become detached, evidently because the metal screws holding it to the door's metal frame no longer engage with their holes in the plastic handle (the holes must have lost some thread). Some screws holding the oven frame in a chipboard surround are spinning in a similar way, although I don't think they affect functionality (it seems solid enough). I thought about repairing both with superglue, but read that PVA can produce cyanide gas at temperatures above 230C so this seems rather risky. As Heat Mate is OK to 300C, is it the best product to fix the various screws in place, or is some other adhesive/sealant better?

By Ozaru - - 01 September 2009
  • Have you tried different bolts, either longer ones of the same size to use the thread further in the handle, or bigger ones and rethread the plastic of the handle. This stuff probably would do the job but it is a big cartridge and you would only need a small amount. The holes in the chipboard you could pack out with matchsticks (remove the heads obviously). Works as a sort of DIY rawlplug. By hemlock1961 - East Sussex - 13 February 2010
  • Answering my own query after waiting in vain for anyone else to do so... and after hitting upon the revolutionary idea of calling the manufacturer (doh!)... Their technical services department were very helpful, and said (a) the sealant is not 'structural' so might pull straight out again if subjected to any significant load; (b) two-part epoxy resin adhesives (araldite etc.) are fine at high temperatures and stronger than sealants, so that's what I need. There were incidentally other problems I noticed from the docs on the EverBuild website and they confirmed, e.g. 'minimum width 6mm', 'do not use on soft metals such as brass', etc. By Ozaru - - 15 September 2009
Answer this question
By Anonymous - Watford - 10 May 2009
  • You need to scrape the old stuff off and clean off all grease with meths or similar. By hemlock1961 - East Sussex - 13 February 2010
  • Rory from eSpares
    Rory at eSpares says...

    Hi Nigelashley, I'd advise removing as much old sealant as possible, as the new sealant will adhere much better to the surface of the oven.

Answer this question
By mums - - 26 February 2009
  • This is what i have used it for and it has worked (so far!) Pretty easy to apply and oven was used the next day By leicesterpie - - 25 May 2010
  • Rory from eSpares
    Rory at eSpares says...

    Hi Mums, this sealant is made just for this purpose - it will re-stick your door glass just like that.

Answer this question
By waterlily - - 16 January 2009
  • yes it works, but is a bit messy, dont spill any By doedoe - liverpool - 20 January 2009
  • Although the oven has only been used twice since applying the new adhesive it seems to have done the job. It was used to re-fix the inner oven glass (NEFF) which had come adrift after 10 years of regular usage. I'm hopeful that it will last at least another 10 years, when it will probably be time for a new one! Beware though, the sealant / adhesive can be very messy to apply if you haven't done it before. Need to spend time to ensure that the old surfaces are thoroughly cleaned up. By Ricardo - South Cumbria - 19 January 2009
Answer this question

how do you get the back of the oven door of i cant find any screws.and i need to seel the glass which has come loose

By baz505 - southport - 11 January 2009
  • Rory from eSpares
    Rory at eSpares says...

    Hi Baz505, check out our video on how to remove an oven door here: http://www.espares.co.uk/advice/cookers-and-hobs/a/1/1151/how-to-repair-an-oven-door.html

  • The sealant will act as seal - so should be no need to unscrew anything. By Jeanna - Beckenham, Kent - 01 March 2010
Answer this question
By spuddy - - 22 December 2008
  • Yes! By Jeanna - Beckenham, Kent - 01 March 2010
  • Rory from eSpares
    Rory at eSpares says...

    Hi Spuddy This glass sealant will work if you are sticking the seal to your glass oven door.

Answer this question

the glass door on my daughters singe oven fell off and i need to attach it back on with some kind of sealant on the one end. will the above product do?

By Reverand - - 23 November 2008
  • Yes! By Jeanna - Beckenham, Kent - 01 March 2010
  • Rory from eSpares
    Rory at eSpares says...

    Hi Reverand This sealant is designed specially for use with oven glass and will stick your daughter's oven door back together.

Answer this question

the metal rim/surround is lifting up from the work surface in one corner.Do you think this sealant will be suitable

By E Pauer - London SW1A 1RJ - 28 March 2018
  • Dean from eSpares
    Dean at eSpares says...

    We believe this silicone sealant should be suitable for repairs of this type.

Answer this question

Heat Resistant Glass Sealant - 310ml

£17.42
(inc. VAT)
£17.42