Dishwasher NTC Sensor Stock Number: ES731792
Genuine spare part for select Bosch, Neff and Siemens dishwashers
Having problems with Bosch Exxcel SGS45E68GB/64 dishwasher - it starts the programs ok (and heats water so I know the heater and relays are fine) and runs for a period of time but towards the drying cycle the washer is constantly emptying and refilling - never actually dries the dishes. I've measured the resistance on the NTC (165281) and is is open (infinity). The high limit side of the unit reads 0.3 ohms - does this suggest that the NTC is faulty ? Would it give the symptoms I'm seeing.
-
eSpares Staff at eSpares says...
It is unlikely the NTC but you will need to check the float in the bottom and if it has activated check for a leak but if not test the flow meter and the impellor jug.
Dishwasher switch’s on but turns off after about five mins we let it cool down then lights back on buttons then we can start again 1 Answer
Could it be thermostat
-
eSpares Staff at eSpares says...
You will need to determine what component has failed, we have a video to help www.youtube.com/watch?v=yL6A7I_rC2o&t just copy and paste into your browser.
Resistance of heater OK
-
eSpares Staff at eSpares says...
If the heater has tested ok then you would need to test the NTC to determine if it has failed.
The control lights no longer illuminate but the DW has power. The impeller spins briefly and splashes water around and I cannot find any trace of debris in the well. Any ideas please?
-
Dean at eSpares says...
Please see our advice centre for more help www.espares.co.uk/advice/symptom/my-dishwasher-is-not-working just copy and paste the link into your browser.
Dishwasher gets three quarters way through its cycle then stops and knocks all electric off in the house. Dishwasher gets really hot. Same fault on whichever program I set it on. Works perfectly until it gets to the drying stage 1 Answer
Will the problem be the Thermostat?
-
Chris at eSpares says...
The problem is likely to be the water heater not the thermostat.
The valve & NTC Sensor just the quick wash programme having a problem with.
-
Chris at eSpares says...
Check the hose from the 'float chamber on the left of the machine where it feeds into the sump. These machines can block the hose with a build up of grease that will cause the machine to repeatedly stop filling and start emptying then stop emptying and fill again. The hose is only pushed into the sump and held between the sump and float chamber. Remove it and clean if in doubt.
-
Rory at eSpares says...
Hi Brent, this sensor is situated beside the water heater, which is in the base of the dishwasher. To get to it, you'll need to remove the lower basket as well as the filter guard and filter.
if heater unit ok and pcb board ok what else could cause water not to heat up? and and i have to reset to drain 0 Answers
model siemens dishwasher se25a09gb/17
Dishwasher working but not heating up - gotta be the heater or thermostat . Does NTC sensor serve as thermostat. How do you get to heater and NTC sensor without taking whole dishwasher apart. Is there an instruction book available 0 Answers
After some effort and no obvious way to get to the heater and what i now know from your web site to be the NTS sensor i eventually took dishwasher to pieces and have pump, heater, ntc sensor on the workbench (having made diagrams of electrical connections its necessary to disconnect) this model definately not user friendly to access the working bits. Does MTC sensor serve as a thermostat?. With electrical test meter unit shows open circuit across terminals when at room temperature and in boiling water whereas heater elements show good continuity and appear good with no scale build up.
Will this part fit my appliance?
Check Now