Oven Door Hinge Runner Stock Number: ES664231
Genuine spare part for select models of Bosch, Neff and Siemens cookers
Trying to fit oven door hinge runners to a Neff B1641N1GB/09 but cannot get the bottom panel off. Can anyone assist 4 Answers
- Just as Jreidu said for a Neff B1691N0GB oven from circa 2001. Use self-tapping screws in adjacent holes in carcass to the rivet/weld on reassembly and good as new. The hinge runners were the solution to the poor door closing.
- Jreidu. Yes that works. Why on earth do they need to rivet the bottom plate on is beyond me. If you are very dextrous and have fairly small hands you only need to take out two rivets as the bottom plate will then bend back sufficiently to manoeuvre the runner out. The new runners cured the problem. The door shuts perfectly - and tightly now. So thanks again Jreidu. I don't think I would have arrived at this solution myself and it saved me lots of time as a result.
-
Chris at eSpares says...
We are pleased you managed to solve your own problem and thank you for the feedback as this may help others when they face this problem in the future.
- This is an answer to my own question. In trying to remove the bottom plate I removed all the likely looking screws (and quite a few of the less likely ones) but the bottom plate was still firmly attached to the oven. Eventually, after much examination, I noticed that ther were four rivets, one at each corner. I drilled these out and the plate came off easily. Beside each rivet there was a screw hole without any screws fitted. When I reassembled the oven I put a screw in each of these holes although this may not have been necessary since the plate is held in front and back. Incidentally, replacing the runners has cured the long standing problem of the door not closing properly a problem I had already tried to cure by fitting new hinges. Both the old runners are vey badly distorted.
The hinges on my oven seem quite firm yet there is movement in the door from the runners. Do I have to replace these? Is it easy to do? 2 Answers
- Do you have any idea when the video for replacing runners will be on your web-site ?
-
eSparesMalindi at eSpares says...
We cannot say when is the right time to replace your parts. We unfortunately do not have a guide for replacing runners on an oven but we will hopefully have a video up soon.
I have the neff B1641N2GB/05 , door off, and sitting on its front, got the back panel removed, took screws out of one side and bottom panel but panels not budging, are there instructions available or can anyone explain how to access the runners ? 1 Answer
I need to make sure I can access hinge runners before ordering
-
eSpares Staff at eSpares says...
The manufacturer uses rivets to hold the side panels that need to be removed to allow access to the runners, you will need to put self-tapping screws back into the side panels when refitting.
Neff fridge K4664x7gb/01 door will not close properly, can anybody tell me what the problem could be 1 Answer
-
Chris at eSpares says...
These runners can get distorted by the oven door being lowered to quickly. As a result the oven door may not close correctly and allow hot air out of the top.
My oven door doesn't close properly - how do I know whether the runners or the hinges are causing the problem? 1 Answer
- I suspect that in the majority of such situations it is the runner which is the culprit. From an engineering point of view they are the weaker of the two components, and if the door has been (accidentally) overloaded in the past (eg by using it as a shelf when open) then the failure will likely have occurred at the runner. Unfortunately the runner is a bit more complicated to replace!
Would this hinge runner suit neff main oven ...model no 195-301410?
-
Rory at eSpares says...
Hi Neff, we do not stock a hinge runner for your model. Sorry!
Will this part fit my appliance?
Check Now