Tumble Dryer NTC Thermostat with Cable Stock Number: ES1331811
Genuine spare for select models of Beko tumble dryers
Hi I have a Beko drcs68w and it dries clothes fine but it will not switch off I have it on the extra dry setting and always have also it will not let me choose another setting and bleeps when I turn the program knob on every setting except the extra dry setting I've also noticed when I turn the program knob to a different setting and do the reset it beeps on all settings except the the one I did the reset on what could be the problem please?
-
Chris at eSpares says...
For information to diagnose your problem see our video: How to Diagnose Tumble Drier Drying and Heating Problems: www.espares.co.uk/advice/9/2050 It is possible the problem may be the board.
- i have replaced heatingunit and thermostat still not heating cleaned all vents and still no heat
-
Chris at eSpares says...
Moisture is detected by the metal strips of Stock Number: ES1567608 contacting damp clothes. If this is damaged or contaminated or the control board has failed it may show this problem.
Tried reset button. Also tried holding the 2 buttons for 3 secs. Checked the red clip is secure. Door is securely closed. All fuses are ok.
- Have just had this same fault on a Beco tumble dryer and there was a bad track on the main circuit board which I bridged with a thin wire and it is working again, don’t know if this is a temporary cure or not but only time will tell.
-
Chris at eSpares says...
For information to diagnose your problem see our video: How to Diagnose Tumble Drier Control and Program Problems www.espares.co.uk/advice/9/2049
i have followed the video for another beko model but my dryer does not have the release bracket to allow access to the thermostat
-
Chris at eSpares says...
Replacement should be very similar to that shown in the video attached to this part.
I have replaced the heating element on my BEKO DRCS68W twice since the beginning of December but the same problem keeps occurring - the element is on for about 20 seconds and then it clicks off. It won't heat up again unless it's reset. Could this be a fault with the NTC rather than the heating element?
-
Chris at eSpares says...
If the covers are on and there is no blockage of air flow the heater should not cut out and would not need to 'cycle' for several minutes.
having took the back panel off, disconnected the lhs stat and found this was to earth. With this disconnected the dryer works but no heat. Is this a thermostat ?? only the lugs are smaller than the rhs resettable one, and will the replacement have to be a full element as the stats are not screwed on.
-
Chris at eSpares says...
This NTC is fitted at the front and is not a suitable replacement for your part. The thermostat you require is only available with the heater element.
Hi i have watched above video, have took the top off and removed the 3 screws, how do i then remove panel from the machine?
-
Chris at eSpares says...
Slide back 5 to 10 mm and lift off.
-
Chris at eSpares says...
We have now attached a video showing this type of repair to this part.
I have pretty much replaced the whole unit from changing the heating element, main wires, the circuit board and now the themostat. Which is shown in the picture. I was wondering if anything else that is in fault. I've run out of options on how to fix this if it still doesn't heat up. Please help me.
-
Chris at eSpares says...
The control board can also cause this problem. See videos: How to Diagnose Tumble Drier Control and Program Problems http://www.espares.co.uk/advice/9/2049/how-to-diagnose-tumble-drier-control-and-program-problems- and How to Diagnose Tumble Drier Drying and Heating Problems http://www.espares.co.uk/advice/9/2050/how-to-diagnose-tumble-drier-drying-and-heating-problems
Beko tumble drier June 2011.DRCS68S It has started to over heat. I can smell burning and it made a banging sound. It is still working.Still getting hot. It will work fine for about 30 mins then start to overheat.
-
Chris at eSpares says...
It may be the mains filter on the back panel were the power cord comes in that is failing. disconnect the power and examine for signs of damage or smoke.
i have a beko DRVS62W tumble dryer..i need to change the thermostat but i an unsure about how to do it..help me please? many thanks tracy
-
Chris at eSpares says...
This sensor is behind the front control panel on the drum support. If your dryer is not heating check the thermal cut outs on Stock Number: ES1331815
Will this part fit my appliance?
Check Now