Tumble Dryer Bipolar On/Off Switch Stock Number: ES104324
Genuine spare part for select Candy and Hoover tumble dryers
- Ensure MAINS PLUG is removed FIRST. On Hoover HDV6, remove 3 screws at back fascia, retaining chipboard top-cover. Slide out cover and then slide two guide rails off fixed bolts and set all aside. Remove timer dial on front fascia (using rubber glove or similar to get a grip!) -- straight pull. Remove top fixing screws (2) to front fascia. Fascia is now held by plastic tabs in 10mm horizontal slots. Gently nudge fascia to the right to lift from slots. Fascia then hangs by wiring, but switches and electricals can be accessed. Take note of positions for two wires on On/Off switch (there's a black side and a white side). Switch is held in position by two thin black plastic wing-type tabs that open when switch is pressed into housing. Gripping switch, use thin-blade screwdriver or similar to press wings inwards on one tab while gently pulling backwards. Press wings inwards on opposite tab, while still tugging, and switch should then come away. When inserting new switch, press in and ensure wing tabs have opened and switch is secure. Replace wires to appropriate terminals. Re-assemble in reverse order.
-
eSparesMalindi at eSpares says...
Unfortunately we cannot give out technical advice. Please contact an engineer or the manufacturer for more information.
Needed for Hoover HDV6 = can't see on the list, will it be ok? Not obvious how existing switch removed, could you let me know how? Thanks 2 Answers
- Ensure MAINS PLUG is removed FIRST. On Hoover HDV6, remove 3 screws at back fascia, retaining chipboard top-cover. Slide out cover and then slide two guide rails off fixed bolts and set all aside. Remove timer dial on front fascia (using rubber glove or similar to get a grip!) -- straight pull. Remove top fixing screws (2) to front fascia. Fascia is now held by plastic tabs in 10mm horizontal slots. Gently nudge fascia to the right to lift from slots. Fascia then hangs by wiring, but switches and electricals can be accessed. Take note of positions for two wires on On/Off switch (there's a black side and a white side). Switch is held in position by two thin black plastic wing-type tabs that open when switch is pressed into housing. Gripping switch, use thin-blade screwdriver or similar to press wings inwards on one tab while gently pulling backwards. Press wings inwards on opposite tab, while still tugging, and switch should then come away. When inserting new switch, press in and ensure wing tabs have opened and switch is secure. Replace wires to appropriate terminals. Re-assemble in reverse order.
-
Rory at eSpares says...
Hi Rollite The bipolar switch for your Hoover HDV6 tumble dryer can be found here: http://www.espares.co.uk/part/tumble-dryers/hoover/hdv6uk/p/1088/107/0/677491/474520/bipolar-switch.html
I have a Hoover HDV6 tumble drier. the on/ off switch does not click when pushed but the machine will run if the button is held in (we find a matchstick works well) I notice you say that this is a none latching switch so does it mean that my switch is perhaps not faulty after all? Best regards Tim
- it more than likely it's the small electronic board just inside the front up under the top , only difficulty replacing it is the screws that hold it are in the wrong way round , so you need to remove the fascias to do this .
Candy CIC 60 condenser dryer. Power switch not "clicking on" but heat setting underneath works ok. Will this product solve the problem? Many thanks. Lynn in York
-
Rory at eSpares says...
Hi Hateironing, check out this page for possible causes and solution to your problem: http://www.espares.co.uk/advice/tumble-dryers/a/9/117/common-tumble-dryer-faults.html
I require a latching ON/OFF switch for my Candy Nova Tumble Dryer Model CDV 262. Would this switch be suitable? My model No is not displayed in your listing,
-
Rory at eSpares says...
Hi Bluebird This bipolar switch would not be suitable for your Candy CDV262 tumble dryer, however I'm happy to say we have just the switch for your model here: http://www.espares.co.uk/part/tumble-dryers/candy/cdv262/p/1088/775/0/511084/474520/bipolar-switch.html There'll be no disorder to your tumble dryer any more!
Hoover Tumble Dryer model HNV160-80 When I push the start button it buzzes and won't start, but if I hold the button in then it keeps going! Please can you advise me
Will this part fit my appliance?
Check Now